The Rowe PDM60 is a compact and feature rich programmable power hub designed for use in any switched 12V application where up to 6 circuits and 60 amps of protection are required. There is no better way to add power distribution to any automobile, boat, UTV, motorcycle or tractor.
What Settings Are Available ?
Key On : Set any or all of the 6 circuits to activate via the key on function.
Ground Switch : Set any or all of the 6 circuits to activate via a simple switch wired to chassis ground.
Key On or Ground : Set any or all of the 6 circuits to activate via the key on function or a ground switch function when the key is off. Such uses include lights, intercooler pumps, electric water pumps and fan circuits.
Key On and Ground : Set any or all of the 6 circuits to activate when the key is on and a ground switch function is used. Such uses include winches, nitrous systems, methanol systems.
Delay Start : Set any or all of the 6 circuits to activate on a delay you specify per circuit. Such uses include delay start on vehicles with heavy electric loads or cold climate use.
Delay Stop : Set any or all of the 6 circuits to remain on for a period you specify after key off. Such uses include water and intercooler pumps or exterior lighting.
Why is the PDM60 Superior ?
The PDM60 is the quickest and easiest way to install serious power distribution in anything 12V without needing to hand wire an additional fuse block or install multiple relays and taps.
Each of the 6 outputs can be programmed for both function and power handling independently and re programmed as many times as needed should your power requirements change.
The PDM60 is fully encapsulated in an industrial grade, hi-temp material to make it fully water, weather, and dust proof from even the harshest of environments and is manufactured in the USA.
The PDM60 is CAN BUS compatible for hassle free installation into the latest vehicles.
Whats included In a single PDM60 kit ?
PDM60 advanced power distribution module (2.0" x 3.75" x 0.9")
PDM60 proprietary programming cable and instructions on how to download the included software and program your unit in seconds.
1 Black 9” ground cable with protective boot specific for motorcycle and UTV battery terminal connection.
A large selection of terminals and Posi-Lock / Posi-Tap connectors to help complete your installation.
Free Canada Post expedited delivery across Canada with full insurance and a signature confirmation to ensure your parcel arrives at its destination safely. (PO BOXES ARE OK)
Free Expedited delivery in the continental USA.
How does the PDM60 protect your circuits ?
The Rowe PDM60 continually monitors and evaluates each of the 6 circuits individually based on your programmed amperage settings and filters out voltage spikes to trigger only on true fault conditions.
Simply correcting the fault in the circuit will allow the circuit to function correctly again without the need to store and replace a mechanical fuse as in a conventional panel..
Who should be ordering a PDM60 :
Professionals wiring service vehicles for lighting and advanced electronics that must perform flawlessly long term.
Enthusiasts wiring high performance motorsport applications to control various pumps and triggers with bomb proof reliability in the smallest and lightest form factor.
DIY customers looking for the cleanest, easiest and most advanced way to add accessories like heated seats, light bars and winches to their personal project vehicles.
Anyone considering installing a under hood or secondary fuse panel to a vehicle or boat.
PDM60 LED indicator lights by color:
Green LED = Active and Protected
Red LED = Fault Detected - Circuit Disabled
Orange LED = Inactive Circuit
Off = Circuit Not In Use
Rowe Electronics PDM60 Warranty Information
The PDM60 power distribution module is covered by a manufacturers limited warranty for one year from the date of original purchase against defects in materials and / or workmanship. Registration instructions are provided.
Please note that this limited warranty does not cover installation error, installation damage, misuse, or incorrect wiring and is limited to the cost of the module.
Our starting price is lower than the manufacturer's "minimum advertised price." As a result, we cannot show you the price on the product page.
Pricing excludes professional installation, which typically costs $300 - $450 per row of seating. Katzkin strongly recommends that you use an authorized Katzkin
installer.
Our price is lower than the manufacturer's "minimum advertised price." As a result, we cannot show you the price on the product page.
You have no obligation to purchase the product once you know the price. You can simply remove the item from your cart.
Contact Css Co.control
Contact us with questions or to request a custom quote. We are available Monday through Friday, 8am to 5pm Pacific.
